How to Replace Side Cover Slider Parts on Sony WH-XB910N Headphones

Is the side slider cover on your Sony WH-XB910N cracking or falling apart so you can’t wear them anymore? This guide shows you how to install our upgraded slider cover kit with the two tools that come in the box.

Watch: Sony WH-XB910N side slider cover installation

Ready to order? Grab the XB910N slider upgrade kit.

Usually ships within one business day from Fox Lake, IL. Small USA family business, established in 2014.

Shop the XB910N Slider Kit: $44.99

What You’ll Need

  • Inner and outer side cover parts for both sides (left and right)
  • Small Phillips screwdriver (included with the kit)
  • Spudger pry tool (included with the kit)
  • The original screws from your headphones (you will reuse them)

You may also need:

  • A small clamp or pliers, only if the new parts flare out after snapping together

Step-by-Step: How to Replace the Sony WH-XB910N Side Slider Covers

Step 1: Remove the two screws

Two screws hold the slider assembly together. Remove them with the small Phillips screwdriver and keep them somewhere safe. You will need them for the new parts.

Tip: Work over a desk or table so you don’t lose the tiny screws.

Step 2: Pry the two pieces apart

Use the spudger to gently pry the two pieces apart, working your way down toward the headband. Take your time.

Tip: There is a wire between the two parts. Be careful not to damage it with the tool.

Step 3: Remove the ear cup mounting screws

Once the pieces are apart, two mounting screws hold the ear cup to the parts. Remove them with the Phillips screwdriver.

Step 4: Remove the old parts

Sweep the inner part out with a downward motion, then slide the outer part off. Check the small metal tab that holds the slider pieces on. It should be intact, not bent, damaged or missing.

Step 5: Mount the ear cup to the new inner part

Line up the ear cup’s metal hinge bracket with the two screw holes on the new inner part, then secure it with the two mounting screws. It may take a little patience to get it aligned.

Tip: Don’t over-tighten. Too much force can strip the new parts.

Step 6: Slide on the new outer piece

Slide the new outer slider piece into place.

Step 7: Snap the parts together

Make sure the wire is tucked between the two parts, not on the outside. Extend the band a bit if needed, then press the parts together. You may hear a snap. If the parts flare out, squeeze them so the small hook seats in its track, using a small clamp or pliers if needed.

Step 8: Install the screws and test

Put back the two screws from step 1. Check that the headband extends and retracts and the ear cups move freely, then repeat on the other side.

Get your XB910Ns wearable again.

Usually ships within one business day from Fox Lake, IL. Small USA family business, established in 2014.

Get the XB910N Slider Kit: $44.99

Why Do the Sony WH-XB910N Slider Covers Break?

The slider cover on the side of the headband takes stress every time you adjust or flex the headphones. Over time it cracks and falls apart, and once it does the headphones won’t stay on your head. Sony has the same weak spot on several models.

Our replacement kit is designed and made in the USA from PA-Nylon 12 and comes with a lifetime warranty. It extends with clicks like the original, and the texture is similar. The parts are black and won’t exactly match the original color.

All Replacement Parts for the Sony WH-XB910N

More parts made to fit the XB910N:

Ear Pads

XB910N Replacement Ear Pads

Black or Blue, mounting rings installed, pry tool included. $19.99

Shop Now

Headband

XB910N Headband Pad Cushion

Replacement headband pad. $17.99

Shop Now

Battery

XB910N Replacement Battery

OEM battery. $29.99

Shop Now

Frequently Asked Questions

Are tools included?
Yes. The kit includes a small Phillips screwdriver and a spudger pry tool. You reuse the original screws.

Does the kit cover both sides?
Yes. It includes the inner and outer slider parts for the left and right side.

Do the new parts adjust like the originals?
Yes. They extend with clicks like the original parts.

Are these original Sony parts?
No. They are CentralSound replacement parts, designed and made in the USA from PA-Nylon 12. They are black and will not exactly match the original color.

Will this fit the WH-XB900N?
No. This kit fits the WH-XB910N (YY2951) only. For that model, see our WH-XB900N slider kit.

DISCOVER · REPAIR · REVIVE

Your XB910Ns aren’t done yet.

Usually ships within one business day from Fox Lake, IL. Small USA family business, established in 2014. 20k+ positive reviews.

Shop the XB910N Slider KitBrowse All Sony Parts